manualshive.com logo in svg

Avital AviStar 3300, Руководство по установке

Поделиться
Скачать
Avital AviStar 3300 Скачать руководство пользователя страница 19

© 2000 Directed Electronics, Inc. Vista, CA

19

In addition, you must connect a tan (+) shut-down input to the yellow wire on the relay satellite ribbon cable.

This prevents the remote start system from activating if the key is left in the "run" position. If your remote start

system only has one tan input, you must use diodes to isolate the ignition circuit from the brake switch input.

However, due to future manufacturer changes in vehicles, it is possible that this may not apply to all vehicles.

In addition, color variations are possible from model to model; make sure to test the circuit carefully. Please call

DEI Technical Support if you need assistance in making this interface.

IMPORTANT! 

Once the interface is complete, attempt to remote start the vehicle with the door

closed and the key in the ignition. The vehicle should not start. If it does, recheck the connections.

General Motors trucks, sport utility vehicles and column shifting passenger vehicles:

Pre-1996 Dodge Dakota pickups with 2.5 liter motors:

Содержание AviStar 3300



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды