Avital AviStar 3300 страница 36 Скачать руководство пользователя

Страница: 36 / 50

system features learn routine

The System Features Learn Routine dictates how the unit operates. It is possible to access and change any of

the feature settings using the Valet/program switch. However, this process can be greatly simplified by using the

optional Personal Computer Interface or Bitwriter (

p/n 998T

). Any of the settings can be changed and then

assigned to one of up to four transmitters. This feature is called Owner Recognition. Each time that particular

transmitter is used to disarm the system, the assigned feature settings will be recalled. Owner Recognition is

only possible when programming the unit via the computer interface or hand-held programmer.

If using the Bitwriter or PC Interface to program the System Features Learn Routine, you may lock the unit

so that the features cannot be altered via manual programming with the Valet switch. If you later wish to

program the system manually, you must unlock the unit using the Directed Bitwriter or PC Interface before you will

be able to reprogram the features. If the siren generates one long chirp when attempting to program the unit, this

indicates that the unit has been locked and must be unlocked with the Bitwriter or PC Interface before proceeding.

To enter the System Features Learn Routine:

Open a door. (

The GREEN wire, H1/5, or the VIOLET, H1/7 must be connected.)

Ignition.

Turn the ignition on, then back off. (The heavy gauge PINK wire of the relay

satellite must be connected.)

Select a Menu.

Press and

HOLD

the Valet/Program switch. (The Valet/Program switch must

be plugged into the blue port.) After three seconds the siren will chirp once indicating

entry to the Basic Features Menu. If this is the menu you wish to access, release the button

and go on to Step 4. If the button is not released, you will jump to the next menu and the

siren will chirp twice. There are three possible menus. Once you have selected the desired

menu, release the Valet/Program switch.

Select a Feature.

Press and release the Valet/Program switch the number of times corre-

sponding to the feature you wish to change. For example, to access the third feature, press

and release 3 times. Then press the button once more and

HOLD

it. The siren will chirp the

number of times equal to the feature you have accessed.

Program the Feature.

While

HOLDING

the Valet/Program switch, you can toggle the

feature on and off using the remote transmitter. Pressing the button that arms the system

will select the one chirp or default setting. Pressing the button that disarms the system

(or the Channel Two button when in the single button arm/disarm configuration) will

select the two chirp setting.

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды