Avital AviStar 3300 Скачать руководство пользователя

Страница: 45 / 50

When entering Timer Mode, the engine should shut down. The parking lights (if connected) will flash four times

and the engine will restart. The system is in Timer Mode. The engine may be allowed to run for its programmed

run time, or the transmitter can be used to shut down the engine. Either way, the remote start system will restart

the engine again in three hours. Timer Mode is exited automatically after the sixth run cycle.

To enter or exit timer mode manually:

1. Make sure the remote start system is not operating the engine.

2. Turn the ignition on.

Timer Mode will be exited and the parking lights will flash four times.

table of zones

When using the Diagnostic functions, use the Table of Zones to see which input has triggered the system. It is

also helpful in deciding which input to use when connecting optional sensors and switches.

NOTE:

During remote start, all zone inputs except the door trigger input are bypassed until 5

seconds after the remote start has shut down.

ZONE NO.

TRIGGER TYPE

INPUT DESCRIPTION

Hood and/or Brake Trigger

GRAY and BROWN wires on the 6-pin shutdown harness.

Multiplexed Input

Heavy impact from the shock sensor.

Door Trigger

GREEN (H1/5) and VIOLET (H1/7).

Multiplexed Input

BLUE (H1/6)

NOTE

: The Warn Away response does not report on the LED.

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Похожие инструкции для AviStar 3300

Бренды по названию

Популярные бренды