Avital AviStar 3300 Скачать руководство пользователя страница 13

Страница: 13 / 50

secondary harness (H2) wire connection guide

This wire provides a (-) 200mA output whenever the transmitter button(s) controlling Channel 4 is pressed. This

output can be programmed to provide the following types of outputs (see also the

Feature Menus

section):

■

Validity:

Output that will send a signal as long as the transmission is received.

■

Latched:

Output that will send a signal when the Channel 4 button(s) is pressed and will continue until the

same button(s) is pressed again.

■

Latched, reset with ignition:

Similar to the latched output, this type of output turns on the first time the

Channel 4 button(s) is pressed and turns off the next time the same button is pressed. This type of output

additionally stops and resets whenever the ignition is turned on and then off.

■

30-second timed:

Output that will send a continuous signal for 30 seconds.

■

Second unlock output:

This output can also be programmed to provide a second unlock pulse whenever the

disarm button is pressed within 15 seconds after disarming the system. This setting could be used to unlock

the passenger doors when installing progressive door locks, for instance.

NOTE:

Programming Channel 4 for second unlock will link the RED/WHITE wire to the unlock button. Pressing

the unlock button once will send the output to the H4/A or H4/C unlock output. Pressing the unlock
button a second time within 15 seconds will send a negative (-) unlock pulse to the RED/WHITE wire.

IMPORTANT!

Never use this wire to drive anything but a relay or a low-current input! This transis-

torized output can only supply 200 mA, and connecting directly to a solenoid, motor, or other
high-current device will cause the module to fail.

This wire sends a negative pulse every time the remote start is activated. This can be used to pulse the disarm wire

of the vehicle's factory anti-theft device. Use a relay to send a (-) or (+) pulse to the disarm wire as shown in the dia-

grams below. This wire can also be used as a special accessory output. (See

Feature Descriptions

section of this guide.)

Relay for Negative (-) Disarm Wire

Relay for Positive (+) Disarm Wire

H2/2 LIGHT GREEN/BLACK (-) factory disarm output

H2/1 VIOLET/BLACK 200 mA (-) channel 4 output

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Бренды по названию

Популярные бренды