Avital AviStar 3300 Скачать руководство пользователя страница 42

Страница: 42 / 50

2-8 DOUBLE PULSE UNLOCK ON/OFF:

Some vehicles require two pulses on a single wire to unlock the doors.

When the double pulse unlock feature is turned on, the BLUE H4/C wire will supply two negative pulses instead

of a single pulse. At the same time, the GREEN H4/A wire will supply two positive pulses instead of a single pulse.

This makes it possible to directly interface with double pulse vehicles without any extra parts.

2-9 FACTORY ALARM DISARM WITH CHANNEL 2:

In the default setting the H2/2 factory alarm disarm output

will disarm the factory alarm system any time the button(s) controlling Channel Two is pressed.

2-10 CHANNEL 4 VALIDITY/LATCHED/LATCHED RESET WITH IGNITION/30 SECOND TIMED/SECOND UNLOCK

OUTPUT:

Channel Four can be programmed for these output configurations. The unit is set to the default valid-

ity output. To change the configuration, use the two-chirp setting to toggle through the different configurations.

(Refer to the H2/1 VIOLET/BLACK wire description in the

Secondary Harness Wire Connection Guide

section of this

manual.)

3-1 ENGINE CHECKING ON/OFF:

In the default setting the remote start will monitor either the vehicle's tach

wire or voltage depending on the programming of feature 3-2. If programmed OFF the vehicle will crank for the

programmed crank time (feature 3-5) and will not verify with tach or voltage that the car is running. In the OFF

setting, if the vehicle fails to start, the ignition can stay on for the entire run duration. Using tach or voltage

check is always recommended if possible.

3-2 CHECKING TYPE TACH/VOLTAGE:

Selects the method of engine monitoring. If set to TACHOMETER the unit

will reference the learned tach signal to disengage the starter. In addition it will monitor the RPM and shut down

if the engine RPM is too high or too low. When set to VOLTAGE, the unit will crank the starter for the programmed

time and then attempt to sense that the engine is running by detecting an increase in voltage. The threshold

for the voltage check is selectable in feature 3-6.

3-3 RUN TIME 12, 24, 60 MINUTES:

Selects the time in minutes that the system will operate the engine

until the system "times out". This is the maximum operation period and the system may be shut down

using a shutdown at any time. Using the Bitwriter, the run time can be programmed for any duration from 1-60

minutes.

3-4 PARKING LIGHTS FLASHING/CONSTANT:

In the default setting, the unit will flash the vehicle's parking

lights (if connected) while remote started. The constant setting will turn the parking lights on solid for the entire

run duration.

3-5 CRANK TIME 0.6/0.8/1.0/1.2/1.4/1.6/1.8/2.0/4.0 SECONDS:

If the unit is programmed for no engine

checking or voltage sense, the crank time must be set to the appropriate duration. The default setting is 0.6

second. If a different crank time is desired, select feature 3-5 and select either 0.6 second by using the one-

chirp setting or toggle through the higher settings by using the two-chirp settings.

menu #3 - remote start options

Содержание AviStar 3300



















































Результаты поиска

Содержание AviStar 3300

Отзывы:

Бренды по названию

Популярные бренды

Avital AviStar 3300, Руководство по установке

Результаты поиска

Содержание AviStar 3300

Отзывы:

Бренды по названию

Популярные бренды