Avital AviStar 3300 Скачать руководство пользователя | Manualshive

Страница: 35 / 50

background image

© 2000 Directed Electronics, Inc. Vista, CA

35

multi-level security arming

Multi-Level Security Arming is a feature that allows the user to select which of the system's inputs or sensors

will be active and which will be bypassed when the system is armed. (See

Table of Zones

section of this guide.)

Multi-Level Security Arming can only be accessed from a standard configuration transmitter. Pressing the arm

button of the standard configuration transmitter again within five seconds of arming the system will activate

the Multi-Level Security feature. Each time the arm button is pressed again, a different security level is selected.

The different levels of security are selected as follows:

■

Pressing

one time: The siren chirps once. The system is armed.

■

Pressing

a second time within five seconds: The siren chirps twice followed by a long chirp. Zone Two

is now bypassed.

■

Pressing

a third time within five seconds: The siren chirps three times followed by a long chirp. Zone

Four is now bypassed.

■

Pressing

a fourth time within five seconds: The siren chirps four times followed by a long chirp. Zones

Two and Four are now bypassed.

■

Pressing

a fifth time within five seconds: The siren chirps five times followed by a long chirp. All input

zones, except the ignition, are now bypassed.

«
...
33
34
35
36
37
...
»

Содержание AviStar 3300



















































Отзывы:

Нет отзывов

Похожие инструкции для AviStar 3300

Бренд: Hama Страницы: 12

Бренд: Hama Страницы: 12

Бренд: iHome Страницы: 12

Бренд: Hama Страницы: 18

Бренд: Siemens Страницы: 5

Prestige APS-25HJ

Бренд: Audiovox Страницы: 12

Platinum Prestige APS-610a

Бренд: Audiovox Страницы: 10

Бренд: Omega Страницы: 6

Crime Guard 810i6

Бренд: Omega Страницы: 20

Бренд: Omega Страницы: 34

Бренд: Datexx Страницы: 1

Бренд: Equity Страницы: 4

Бренд: Radio Shack Страницы: 7

Бренд: Radio Shack Страницы: 13

Бренд: Macurco Страницы: 4

Бренд: Ambient Weather Страницы: 12

Бренд: Abus Страницы: 120

Бренд: Code Alarm Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды