AudioCodes MediaPack MP-402, Руководство пользователя

Страница: 80 / 160

MP-40x SIP MediaPack BRI Series
SIP User's Manual 80 Document #: LTRT-53301
Table 6-6: ISDN Interface Parameters
Parameter Description
Digit Collection Timeout
[digit-collection timeout
<num>]
Specifies the digit collection timeout in seconds.
Valid range is 1 to 15 sec. Default value is 5 sec.
Digit collection
termination char
[[no]digit-collection
terminating-char <* | # | *#>]
Specifies a character that terminates digit collection.
Valid options include:
ƒ
* = indicates that the number is complete by pressing *
ƒ
# = indicates that the number is complete by pressing #
ƒ
*# = indicates that the number is complete by pressing * or #
ƒ
<empty> (default) = the user cannot indicate completion of the number
Digit collection Max No.
Len
[digit-collection nr-length
<num>
Specifies the maximum number length after which the number is assumed to be
complete.
Valid range is 1 to 30. The default value is 30.
Default Number
[[no]default-calling-party]
The phone number that is used in case the ISDN peer doesn't provide a CLIP. If no
phone number is defined, “anonymous” is used (default).
MSN
[[no]msn <number>]
Defines a phone number suffix for which all calls with the same suffix are accepted
when configured as a PMP user interface. Up to 8 phone number suffixes can be
defined. The maximum length of each number is 30.
Hunt Logic
[hunt-logic < cyclic-down |
cyclic-up | down | up>]
Determines the ISDN port allocation scheme by the ISDN interface for IP-to-ISDN
calls.
ƒ
Up = the highest available free port is used
ƒ
Down = the lowest available free port is used
ƒ
Cyclic-up (default) = the next higher free port is used
ƒ
Cyclic-down = The next lower free port is used
Add Port as Prefix
[no] add-port-as-prefix
If enabled, the ISDN port number of the incoming call is added to the source
number as the prefix.
Add B-Channel as Prefix
[no] add-b-channel-as-prefix
If enabled, the B-Channel number of the incoming call is added to the source
number as a prefix.
Adding the B-Channel will precede the number manipulation.
Default: disabled
Note: if more than one prefix is enabled, see Section
924H
6.2.2.4 “
925H
Order of Prefixes” on
page
926H
81 for order of prefixes.
Add NPI to calling number
[no] add-npi-as-prefix add-
to-calling
If enabled, the NPI from the Calling Number of the incoming call is added to the
source number as a prefix.
Adding the NPI will precede the number manipulation.
Default: disabled
Note: if more than one prefix is enabled, see Section
927H
6.2.2.4 “
928H
Order of Prefixes” on
page
929H
81 for order of prefixes.
Add NPI to called number
[no] add-npi-as-prefix add-
to-called
If enabled, the NPI from the Called Number of the incoming call is added to the
destination number as a prefix.
Adding the NPI will precede the number manipulation.
Default: disabled
Note: if more than one prefix is enabled, see Section
930H
6.2.2.4 “
931H
Order of Prefixes” on
page
932H
81 for order of prefixes.
Add TON to calling
number
[no] add-ton-as-prefix add-
to-calling
If enabled, the TON from the Calling Number of the incoming call is added to the
source number as a prefix.
Adding the TON will precede the number manipulation.
Default: disabled
Note: if more than one prefix is enabled, see Section
933H
6.2.2.4 “
934H
Order of Prefixes” on
page
935H
81 for order of prefixes.