2 6
Flashing light – pulsing mode.
To consecutively change a light-sound alarm’s mode it is required to press
[1]
button. Pressing the
Cancel button causes the going into the programming mode with resetting of the changes made. Pressing the
Select button causes the going into the programming mode with the new mode storage.
8.8 Section 5. Configuration of user’s settings.
8.8.1 Change of user permissions (user rights)
The user access to control the certain loops is regulated by user permissions.
To view and change user permissions it is required to enter:
[5][ N][1]
, where
[N]
– user’s number (
1 .. 8
).
After that one of red indicators
[1] .. [8]
highlights the user’s number and
[1] .. [8]
yellow indicators
lights indicate those AL the user has rights on.
The user has rights to control a zone if the yellow indicator corresponding to the zone is on, and does
not have rights if the corresponding indicator is off.
Removal/setting rights to control the AL is made by pressing the button with the corresponding zone
number
[1] .. [8]
.
Pressing the Cancel button leads to going into the programming mode with resetting the changes
made. Pressing the Select button leads to going into the programming mode with saving the changes made.
8.8.2 Change of authorized user access code
To change the authorized user access code it is required to enter using the number buttons:
[5][N][2]
,
where
[N]
– user’s number (
1 .. 8
).
After that one of red indicators
[1]..[8]
denoting the user’s number starts flashing with frequency 1
Hz.
Further, enter the new user’s code from 1 to 8 characters long using number buttons then press the
Select button. If the entered code is accepted then 2 intermittent sound signals shall sound for a minute.
During this time it is required to repeat the access code entering and press the Select button.
The successful change of the code is accompanied with 3 short sound signals. If entered codes do not
coincide the panel shall issue one long sound signal of low tonality.
To deter unauthorized control of the AL it is
recommended
to change access codes set by default.
Example:
to set the access code of the 2
nd
user that is equal
[1][3][1][2]
you should enter:
[5][2][2]
– 2 short sound signals;
[1][3][1][2] [Select] –
intermittent sound signals;
[1][3][1][2] [Select] –
3 short sound signals. The access code of the 2
nd
user is changed.
8.8.3 Change of engineer access code
Change of the engineer access code occurs in the same way as the change of the user’s access code
but to enter the procedure of password change it is required to enter
[8][2] [Select]
instead of
[5][ N][2].
Unlike authorized user code, maximum length of the engineer access code is extended to 10 characters.
8.9 Resetting panel configuration to factory defaults
This operation resets a panel configuration to the settings indicated in Section 8.11. For that it is
required to consecutively press buttons
[8][1] [Select]
in the programming mode.
After that during 9-10 sec. all four red indicators “Zone” will flash. To confirm the decision made
about resetting to factory defaults you should press the Select button. As a result the panel changes its
configuration in accordance with default settings.
If during the delay none of the buttons has been pressed or any button except for the Select one has
been pressed then the panel returns to the programming mode not downloading default parameters.
8.10 Resetting engineer access code to factory defaults
If the engineer’s access code has been lost which is different to the default access code, then it is
impossible to enter the programming mode in order to change the panel configuration. To change engineer’s
access code to the default code
[1][2][3][4][4][3][2][1]
, follow the steps below:
Содержание ARTON-08F
Страница 1: ...OPERATIONAL MANUAL ARTON 08F FIRE ALARM CONTROL PANEL...
Страница 30: ...31 APPENDIX 2 Dimensions...