Anritsu 3659 Скачать руководство пользователя страница 83

Страница: 83 / 160

Using the 2300-580-R Software with VectorStar ME7838D4

3-12 Mismatched Thru Tests – Port 1/Port 2

3659 0.8 mm Cal/Ver Kit & 2300-580-R PVS UG

PN: 10410-00327 Rev. D

3-33

3-12 Mismatched Thru Tests – Port 1/Port 2

If the

Run All Tests

button on the

Application Interface - Main Menu

tab was selected, the

Matched Thru

tests

(described in

Section 3-11 “Matched Thru Tests – Port 1/Port 2” on page 3-30

is executed first, followed by the

Mismatched Thru

tests described in this section.

If the

Matched Thru

test button was selected, only the steps in this section are executed. When this test is

complete, the program returns to the main menu described

Section 3-9 “Application Interface – Main Menu

Tab” on page 3-25

The entry point for this portion of the verification software depends on the user selections made in the

Application Interface – Main Menu

tab described in

Section 3-9 “Application Interface – Main Menu Tab” on

page 3-25

The dialog box is shown in

Figure 3-39, “ME7838D4 Application Interface – Main Menu Tab” on page 3-25

If only the

Mismatched Thru

button was selected, program execution starts here.

If the

Run All Tests

button was selected, program execution continues here after the

Matched Thru

tests

(described in

Section 3-11 “Matched Thru Tests – Port 1/Port 2” on page 3-30

) have been completed.

Procedure

The

Enter Serial Number Offset Set Mismatch Device

dialog box appears. Enter the serial number of the

offset mismatch device.

Ensure that the correct device is connected.

•

The

Matched Thru

verification standard is the device with one scribe line.

•

The

Mismatched Thru

verification standard is the device with two scribe lines.

Note

The verification devices must be connected to the

0.8 mm Connector Coupler Ports

and not to the

VNA Ports

. Use the torque wrench supplied with the verification kit when tightening the device

connections.

Figure 3-47.

Serial Number Dialog

Note

The verification standards must be connected to the

0.8 mm Coupler Ports

and not to the

VNA

ports

Содержание 3659

































































































































































Результаты поиска

Содержание 3659

Отзывы:

Anritsu 3659, Руководство пользователя, Страница: 83 / 160

Результаты поиска

Содержание 3659

Отзывы: