Anritsu 3659 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 160

Anritsu 3659 Скачать руководство пользователя страница 37

Using the 2300-580-R Software with VectorStar ME7838D

2-9 Application Interface – Main Menu Tab

3659 0.8 mm Cal/Ver Kit & 2300-580-R PVS UG

PN: 10410-00327 Rev. D

2-25

Auto Scale Display Button

This command automatically scales each channel on the Anritsu Vector Network Analyzer. It is the same as
using the VectorStar VNA menus to navigate to and select either the

Auto Scale Active Channel

or

Auto Scale

All Channels

buttons. The full path to these buttons is:

•

MAIN | Scale | SCALE | Auto Scale Active Channel

•

MAIN | Scale | SCALE | Auto Scale All Channels

When the program detects the VNA has finished a sweep, the program auto-scales all four channels before
continuing.
The VNA display during the calibration and verification tests is set to one Channel and four traces. Each trace
display is a paired

Log Mag

(top) and

Phase

(bottom) display showing the following parameters:

•

Upper-left quadrant – S21 – Forward Transmission

•

Upper-right quadrant – S12 – Reverse Transmission

•

Lower-left quadrant – S11 – Forward Reflection

•

Lower-right quadrant – S22 – Reverse Reflection

See

below for a display example. This is a typical display immediately after performing the High

Band calibration. Please note this is for reference only and that the actual data on the VNA display may not be
identical.

Figure 2-36.

MS4640A/B Series VNA Auto Scale Example Trace Display

«
...
35
36
37
38
39
...
»

Содержание 3659

































































































































































Отзывы:

Нет отзывов