manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 41

 

 

 

 

 Maintenance 

 
 
 

 

SPECTRO ARCOS FHX22 — 18.07.2019  

— 41 

 

6.8.3 

Cleaning the lens 

 

 

Notice! Instrument damage/measurement error! 

 

The lens is scratch- and moisture-sensitive. 

 

If you touch the lens surface with your fingers, residues (e.g., grease) will 
stick to the lens surface. These residues are hard to remove. 

 

Check the lens for contamination. 

 

When cleaning the lens, proceed as follows (if necessary): 

 

1. 

Loosen the retaining collar (1) at 
the rear using the OPI tool (2).  

 

Fig. 17 

 

2. 

Insert a clean 'peek' sample 
needle or similar type of object 
(1) through the sampler opening 
from the opposite side.  

3. 

Carefully push the lens (2) out 
on lens cleaning paper. 

 

Fig. 18 

4. 

Clean the contaminated lens using lens cleaning paper or a lint-free soft cloth. 

 

Cleaning of the lens is now complete. 

 

 

1

2

1

2

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды