manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 18

 
 

Transportation/Setting-up 

 

 

 

 

— 18 

SPECTRO ARCOS FHX22 — 18.07.2019 

 

4.2 

Set-up 

 

 

 

Caution! Measurement errors! 

 

If the instrument is subject to vibrations and shocks, measurement errors 
may occur during the measuring process. 

 

The instrument must be installed at a vibration- and shock-free location. 

 

Measurement errors result from temperature differences inside the 
instrument. 

 

The instrument must be installed at a location, where it cannot heat up 
or cool down on one side only. 

 

Observe the following information regarding the instrument's installation: 

 

All connections are located on the right-hand side. 

 

The instrument must be accessible from the front and from both sides for 
maintenance purposes. Set up the instrument accordingly.  

 

A table of corresponding dimensions and load-carrying capacity is required, 
see page 15.  

 

In addition to the space required by the SPECTRO ARCOS FHX22, some 
space is needed for the gas supply, unless fixed gas connections are 
available.  

 

The SPECTRO ARCOS FHX22 is operated exclusively from the front and 
from the right-hand side of the housing. Sufficient space should be provided 
for the computer workstation (keyboard, monitor, printer, and sample changer, 
if necessary) and operating personnel.  

 

4.3 

Ambient temperature 

 

Air conditioning of the room is only required under extraordinary conditions. 
Smaller room temperature fluctuations up to 3°C/h (5.4 F/h) are not accounted due 
to the construction of the instrument. However, one-sided heating or cooling must 
be avoided at all costs. 

The specified values only apply to the recommended ambient temperature range. 
Using the instrument beyond the recommended ambient conditions may lead to 
poorer analytical results. 

 

 

 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды