manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 11

 

 

 

 

 Safety 

 
 
 

 

SPECTRO ARCOS FHX22 — 18.07.2019  

— 11 

 

 

 

 

Notice!  

Warns of activities or conditions that may adversely affect the safety or function of 
the instrument. 

 

 

Information 

Displays information that is important for the correct and safe use of the instrument 

 

 

2.2 

User information 

 

 

Compliance with all safety instructions is mandatory. It's for your own safety. 

 

The instrument - in its transport packaging - may only be transported by 
expert organizations or by specifically trained personnel. 

 

The instrument is front-heavy with its center of gravity located in the optical 
system (front left side of the instrument). 

 

Unpacking, installation, setup and connection of the instrument may only be 
performed by service personnel that is authorized by the manufacturer. 

 

Carry out only operator maintenance work that is described in chapter 6 of the 
operating instructions. Any further services (e.g. technical maintenance) or 
repairs must only be performed by service personnel that are authorized by 
the manufacturer. 

 

During the operation and while performing maintenance tasks compliance 
with safety instructions and accident prevention regulations is mandatory. 

 

The safety measures must be checked following every technical maintenance 
or repair activity. The checking procedure is carried out in accordance with 
DGUV V3 (German Social Accident Insurance) or an equivalent national 
regulation. 

 

Compliance with the maintenance schedule specified by the manufacturer 
and recording all maintenance activities is mandatory. This will maintain the 
operational safety of the instrument. 

 

Never tamper with the safety devices! If it is suspected that a safety device 
does not work properly, shut down the instrument immediately! Please 
contact your Service Center. 

 

Please observe the information labels provided on the instrument.  

 

 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды