manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 19

 

 

 

 

 Transportation/Setting-up 

 
 
 

 

SPECTRO ARCOS FHX22 — 18.07.2019  

— 19 

 

 

4.4 

Dust load 

 

Avoiding contamination problems in the analysis requires a relatively dust-free 
environment. 

The maximum dust load should not exceed 36 million particles (0.5 µm or larger) 
per cubic meter of air. Operating the instrument in an environment with a higher 
dust load shortens maintenance intervals and may damage the instrument. 
Example for comparison: A usual, clean office environment contains 18 to 36 
million particles per cubic meter of indoor air. 

To avoid instrument damage, the instrument must also be set up in an 
environment which is free from corrosive vapors. 

 

4.5 

Storage 

 

Storage conditions:  

 

Unit must be stored in a dry place 

 

Room temperature 2°C–40°C (35.6°F–104°F) 

 

Avoid storing the instrument at very low temperatures. 

 

 

 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды