manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 12

 
 

Safety 

 

 

 

 

— 12 

SPECTRO ARCOS FHX22 — 18.07.2019 

 

 

 

Only genuine spare parts must be used when repairing the instrument. The 
use of non-genuine spare parts will make the CE Declaration of Conformity 
null and void. Excepted are spare parts from manufacturers approved by 
SPECTRO. 

 

Only the use of genuine spare parts and consumables ensures the safe 
operation and achievement of the specified output. This applies especially to 
all components of the sample introduction system and, in particular, to the 
plasma torch. 

 

The instrument may only be operated on networks with PE protective 
conductor (PE). 

 

Only use the instrument in dry ambient conditions. 

 

If an instrument is positioned on a sloped surface and equipped with wheels, 
it may roll away during the operation. Secure the instrument while in 
operation. This applies also when the instrument is being transported. 

 

Compliance with the relevant safety regulations when using tools and 
operating equipment is mandatory. 

 

Prior to opening the instrument, disconnect the power plug. 

 

2.3 

Intended use 

 

Only liquid samples may be directly analyzed with this instrument. 

 

 

2.4 

Prohibited operating conditions 

 

Do not operate the instrument if one of the following conditions exists: 

 

If the instrument is faulty or damaged. 

 

If the instrument is not maintained at regular intervals. 

 

If the ambient conditions do not comply with the specification. 

 

If the area where the instrument is used is not a commercial/industrial 
premise. 

 

 

 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды