manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 20

 
 

Transportation/Setting-up 

 

 

 

 

— 20 

SPECTRO ARCOS FHX22 — 18.07.2019 

 

 

4.6 

Gas supply 

 

 

 

Information! Measurement errors! 

 

Impurities in the argon supply will produce measurement errors and/or will 
make ICP operation impossible. 

 

Ensure oil and grease-free installation of the argon supply line. 

 

An argon supply system is required for the instrument. 

A suitable pressure reducer is required for the argon supply system (bottles or 
liquid gas tank). 

 

Adjustable output pressure 0 to 10 bar 

 

It is imperative not to exceed a maximum argon inlet pressure of 8 bar 
(116 psi). 

The tubing for the argon supply system is included in SPECTRO’s scope of supply 
(5 m long, OD/ID = 8/6 mm). This tubing is screwed to the connection point on the 
right-hand side of the instrument. The connection point to the instrument is 
included in the scope of supply. The connector on-site is customer-specific and, 
therefore, not part of the delivery. 

The following flow quantities are used for aqueous samples during normal 
operation: 

 

Coolant: 

9 to 20 l/min, typically 12 l/min 

Auxiliary gas: 

0.6 to 3 l/min, typically 0.8 l/min 

Nebulizer gas: 

0.4 to 1.5 l/min, typically 0.8 l/min 

 

 

 

 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды