manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 37

 

 

 

 

 Maintenance 

 
 
 

 

SPECTRO ARCOS FHX22 — 18.07.2019  

— 37 

 

 

9. 

Clean the spray chamber. 

 

First, use a suitable diluted acid solution (e.g., hydrochloric acid or nitric 
acid 1:10). 

 

Hazardous substance! 

 

Observe the corresponding information on hazardous materials. 

 

After this, use a laboratory cleaning agent for removing traces of fatty 
substances (streaks) if required.  

 

Now flush the spray chamber thoroughly with distilled water.  

10.  Reinstall the components. 

11.  Optimize the nebulizer gas flow, see page 38. 

 

Cleaning of the spray chamber is now complete. 

 

6.5 

Checking the aerosol formation of the nebulizer 

 

In order to proceed with the inspection, follow the steps below: 

1. 

Remove the nebulizer, see page 35, but without disconnecting the argon 
connection. 

2. 

Call up the “Solid State Generator” menu item via the instrument control 
parameter dialog. 

3. 

Adjust the nebulizer gas flow determined for the nebulizer. 

 

4. 

Using a spray bottle, force 
distilled water through the 
nebulizer connection for sample 
introduction. 

 

The spray coming out must 
be evenly V-shaped. If this 
is not the case, the 
nebulizer may be clogged 
and must be cleaned, see 
page 35. 

 

Fig. 13 

5. 

Reinstall the components. 

 

Checking of aerosol generation is now complete. 

 

 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды