Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 17

Страница: 17 / 55

Transportation/Setting-up

SPECTRO ARCOS FHX22 — 18.07.2019

— 17

Transportation/Setting-up

General information:



The instrument is front-heavy with its center of gravity located in the optical
system (front left side of the instrument).



The instrument is open underneath, and therefore, unstable during transport.



The instrument weighs approx. 240 kg (~ 530 lbs) and its weight is not evenly
distributed.



The instrument must not be transported without the shipping pallet (bottom
plate) included in the supply. For additional information, please contact your
responsible SPECTRO Service Center.



The instrument, in its transport packaging, may only be transported by expert
organizations or by specifically trained personnel.



Only service personnel authorized by the manufacturer are permitted to
unpack, install, set up and connect the instrument.

Notice – Damage to instrument!

There is a risk of damage to the instrument whenever it is moved to another
location after it has been set up.



Please contact the SPECTRO Service Department regarding this matter.

4.1

Space requirements

Fig. 6

756 mm

Содержание SPECTRO ARCOS FHX22
























































Результаты поиска

Содержание SPECTRO ARCOS FHX22

Отзывы:

Бренды по названию

Популярные бренды

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание SPECTRO ARCOS FHX22

Отзывы:

Бренды по названию

Популярные бренды