manualshive.com logo in svg

Ametek SPECTRO ARCOS FHX22, Оригинальная инструкция по эксплуатации

Поделиться
Скачать
Ametek SPECTRO ARCOS FHX22 Скачать руководство пользователя страница 33

 

 

 

 

 Maintenance 

 
 
 

 

SPECTRO ARCOS FHX22 — 18.07.2019  

— 33 

 

 

 

6. 

Clean the components of the 
plasma torch. 

 

Place the glass components 
of the plasma torch in aqua 
regia (a mixture of one part 
concentrated nitric acid and 
three parts concentrated 
hydrochloric acid). 

 

Hazardous substance!  

Observe the corresponding 
information on hazardous 
materials. 

 

Let the acid/cleaning 
solution act for approx. 15 
minutes. 

 

Then rinse the plasma torch 
with distilled water and dry it 
completely.  

 

 Fig. 10 

7. 

Clean the holder and the sleeve with a lint-free cloth and visually inspect.  

 

The O-rings and the seal remain in the holder or sleeve in this process. 
Replace the O-rings and the seal if damaged. 

8. 

Re-mount the plasma torch. 

 

The same steps, carried out in reverse order, are used for mounting the 
plasma torch, see point 5. Insert all of the glass elements up to the stop. 

 

 

 

Содержание SPECTRO ARCOS FHX22
























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды