![background image](http://html1.mh-extra.com/html/ametek/sorensen-asterion-dc-asm/sorensen-asterion-dc-asm_programming-manual_2931303069.webp)
Asterion DC Multioutput Series
Programming Manual
9-52
M330517-01 Rev C
CAUTION!
External User Control interface signals are isolated from negative output terminal;
Isolation voltage is rated for
±
600 V
RMS
, maximum; operation of Isolated Analog
Interface signals should be at SELV safety voltage conditions to chassis ground.
9.2.1
Fault
Hight state in the following pin indicates the Fault in the power supply. Fault Signal Pin is 3
and return is 8 for Channel 1, pin 12 and return is 17 for Channel 2 and pin 21 and return is
26 for Channel 3. Fault Signal Pin become High whenever there is a fault recorded in the
Protection Condition Register. An exception to this Constant Voltage Operation (Bit 0),
Constant Current Operation (Bit 1) and Constant Power Operation (Bit 2), as they indicate
the operating status of the power supply.
Low state: 0.3 V max
High state: Minimum 3V and Maximum Current is 0.5 A
Following is the list of faults that can be generated:
Bit Hex Value
Description
Explanation
Actions
3
0x08
Overvoltage
Protection
Fault
Output voltage
exceeded Over
Voltage trip
limit.
•
Check sufficient margin between
set voltage and OVP limit
4
0x10
Over
Temperature
Fault
Power supply
internal
hardware
temperature
exceeded limit
•
Check and make sure there are
no Air blockage in the front and
rear of the power supply. Make
sure Ambient temperature and
the Operating Power limit with
input line condition is as per the
Specifications. If fault persists,
Contact factory
5
0x20
External
Shutdown
External
Shutdown
activated from
External User
Interface
Control
Connector
•
Make sure Pin 7 and Pin 8 are
connected for disabling External
Shutdown of channel 1, Pin 16
and Pin 17 are connected for
disabling External Shutdown of
channel 2, Pin 25 and Pin 26 are
connected for disabling External
Shutdown of channel 3.
6
0x40
Foldback
Mode
Operation
Trip activated
due to foldback
operation
setting
•
Check the foldback operation
setting from
OUTP<n>:PROT:FOLD? Query
and modify as required
7
0x80
Remote
Programming
Error
Power supply
remote
programming
command is
incorrect
•
Verify the SCPI command sent
from remote communication
interface is as per programming
manual.
Содержание Sorensen Asterion DC ASM
