Ametek Sorensen Asterion DC ASM, Руководство по программированию

Страница: 122 / 162

Asterion DC Multioutput Series
Programming Manual
M330517-01 Rev C 12-105
PROGram:INITializing?
This query returns 1 after mains power-on, and continues to
return 1 until the program/sequence functionality is fully
initialized, after which point 0 is returned. Do not attempt to
use any of the other sequence related commands--i.e.,
commands in the SCPI PROG command tree --while
program/sequence functionality is initializing. (Typical
initialization time is approx. 15 seconds after power-on.)
N
PROGram:CATalog?
Lists all the defined sequence names. The format for the
response to the query is a list of comma-separated test
names.
C
PROGram:[SELected]
Selected section of program subsystem C
PROGram:[SELected]:ARM
Prepares the presently selected sequence for execution; this
command may take a few seconds depending the length of
the selected sequence and all subsequences that the
selected sequence may depend upon. The command to use
to execute an armed sequence is
PROG:STAT RUN
.
N
PROGram:[SELected]:ARM?
A return of 1 means the sequence is armed.
A return of 0 means it is not.
N
PROGram:DEFine <step#>,
VIMODE, <volts>, <amps>,
<ovp>, <s>
Programs the
VIMODE
sequence command into the selected
sequence (see
PROG:SEL:NAME
command) at <step#>.
The following values set by this command: voltage <volts>,
current <amps>, over voltage protection <ovp>, and duration
of <s> seconds. <s> may have a decimal value with a
granularity of 0.001 seconds. This command is valid for
steps 1 thru 20.
C
PROGram:DEFine <step#>,
RAMPTOV,<start
volts>,<end volts>,
<amps>, <ovp>,<s>
Programs the
RAMPTOV
sequence command into the
selected sequence at <step#>. The following values are
programmed: starting and ending voltage ramp values <start
volts> and <end volts>, current <amps>, over voltage
protection value <ovp>,and voltage ramping duration in <s>
seconds. <s> may have a decimal value with a granularity of
0.001 seconds. This command is valid for steps 1 thru 20.
C
PROGram:DEFine <step#>,
RAMPTOC, <volts>, <start
amps>,<end amps>, <ovp>,
<s>
Programs the RAMPTOC sequence command into the
selected sequence at <step#>. The following values are
programmed: the starting and ending current ramp values
<start amps> and <end amps>, voltage <volts>, over voltage
protection <ovp>,and current ramping duration in <s>
seconds. <s> may have a decimal value with a granularity of
0.001 seconds. This command is valid for steps 1 thru 20.
C
PROGram:DEFine <step#>,
POWERSETTINGS, <watts>,
<volts>, <amps>, <ovp>,
<s>
Programs the constant power POWERSETTINGS sequence
command into the selected sequence at <step#>. The
following values define the power setting: constant power
limit <watts>,voltage limit<volts>,current limit<amps>,over
voltage protection <ovp>, and time duration in <s> seconds.
<s> may have a decimal value with a granularity of 0.001
seconds. This command is valid for steps 1 thru 20. If a
VIMODE, or a RAMPTOV, or a RAMPTOC command follows
the
POWERSETTINGS command, then when the
POWERSETTINGS command has completed execution, the
subsequent command will take control and the constant
power mode regulation shall cease. However, if the
POWERSETTINGS command is immediately followed by a
PAUSE command, then as long as the PAUSE is in effect the
constant power mode regulation will continue.
C