AGFA DRYSTAR AXYS Скачать руководство пользователя страница 277

Страница: 277 / 461

DD+DIS033.07E

Repair and Service

Adjustments and Calibrations

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Edition 1, Revision 1

DRYSTAR AXYS

Chapter 3.6 / 25

06-2008 Type

5367/100

Agfa Company Confidential

2.5.4.3

Performing a Film Calibration after the internal Densitometer Calibration

NOTE:

The film calibration after the internal densitometer calibration has to be performed one
time for each tray, where DT2M films are available.

(1) Select menu “Service Engineer

Tools - Enter Service Command
session - 6 Calibration - 1 Film
Calibration”.

(2) Select the input tray with DT2M

films: The calibration film as
shown in Figure 14 is printed and
the measured Dmax is shown.

INPUT TRAY:

FILM CALIBRATION OK

Dmax = 3.69 (XR310)

Default densitometer

536736az.cdr

Measured Dmax

(3) Repeat the film calibration for the

second input tray, if it keeps
DT2M films, too.

Figure 14

2.5.4.4

Performing a Print Head Calibration followed by two Film Calibrations

NOTE:

The print head calibration has to be performed 2 times, if films of width 10” and 14” are
available.

INSTRUCTIONS

(1) Clean the thermal head with a cleaning tissue lightly moistened with Isopropyl -

alcohol. The last cleaning action must be carried out in one way.

(2) In the browser pages - menu 'Service Engineer Tools - Enter Service Command

session' select '6. Calibration - 3. Print Head Calibration'.

(3) Follow the instructions on the browser pages. Refer to Figure 15. See

IMPORTANT note next page concerning tray selection.

(4) Perform two film calibrations for this tray, where DT2M films are loaded – if both

trays keep DT2M film, perform it for both trays. Refer to section 2.5.4.1.

Содержание DRYSTAR AXYS














































































































































































































































































































































































































































































Результаты поиска

Содержание DRYSTAR AXYS

Отзывы:

Бренды по названию

Популярные бренды

AGFA DRYSTAR AXYS, Руководство по обслуживанию

Результаты поиска

Содержание DRYSTAR AXYS

Отзывы:

Бренды по названию

Популярные бренды