AGFA DRYSTAR AXYS Скачать руководство пользователя страница 275

Страница: 275 / 461

DD+DIS033.07E

Repair and Service

Adjustments and Calibrations

DOCUMENT CONTROL NOTE:

The controlled version of this document resides on MedNet. Any printed copy of this document is uncontrolled.

Edition 1, Revision 1

DRYSTAR AXYS

Chapter 3.6 / 23

06-2008 Type

5367/100

Agfa Company Confidential

2.5.4.1 Performing

Film

Calibrations

NOTE:

The film calibration has to be performed two times for each tray, where DT2M films are
available.

(1) Select menu “Service Engineer

Tools - Enter Service Command
session - 6 Calibration - 1 Film
Calibration”.

(2) Select the input tray with DT2M

films: The calibration film as shown
in Figure 12 is printed and the
measured Dmax is shown.

INPUT TRAY:

FILM CALIBRATION OK

Dmax = 3.69 (XR310)

Default densitometer

536736az.cdr

Measured Dmax

(3) Repeat the film calibration a 2

time.

(4) Repeat the film calibration two

times for the second input tray, if it
keeps DT2M films, too.

Figure 12

2.5.4.2

Performing an internal Densitometer Calibration

(1) Select menu “Service Engineer Tools - Enter Service Command session - 6.

Calibration - 2. Internal densitometer calibration”.

(2) Follow the instructions on the browser pages. Refer to Figure 13.

Содержание DRYSTAR AXYS














































































































































































































































































































































































































































































Результаты поиска

Содержание DRYSTAR AXYS

Отзывы:

Бренды по названию

Популярные бренды

AGFA DRYSTAR AXYS, Руководство по обслуживанию

Результаты поиска

Содержание DRYSTAR AXYS

Отзывы:

Бренды по названию

Популярные бренды