Advanced Instruments 4250 Скачать руководство пользователя страница 95

Страница: 95 / 121

Troubleshooting Table

“Sample Probe Failure”

“Sample Probe Open?”

“Standards Reversed?”

“Stir System Failure”

“Supervisor Key

Needed...”

samples contain no bubbles or froth before

testing. Decrease the sample stir amplitude, if

necessary, to avoid generating bubbles before

the freeze buzz occurs. If this does not solve

your problem, you should check the probe

bin number and obtain service if necessary.
Switch the instrument off, then on. Check the

sample probe by running the A/D tests. If the

error message does not persist and other error

messages are not displayed, ignore this mes-

sage. Otherwise, contact Advanced Instruments

for Hot-Line Service.
Switch the instrument off, then on. Make sure

the sample probe is plugged into the main

board. Check the sample probe by running the

A/D tests. If the error message does not persist

and other error messages are not displayed,

ignore this message. Otherwise, contact

Advanced Instruments for Hot-Line Service.
This message will appear during the calibration

procedure if the instrument detects that the low

and high calibration standards may have been

mixed up and were entered in the wrong order.

Repeat current sample, being sure that the stan-

dards are correct.
This error message indicates a problem with

your stir/freeze wire system. Try restarting

your instrument. If this does not solve your

problem, contact Advanced Instruments for

Hot-Line Service.
This feature or action has been locked out by

use of the supervisor/operator keyswitch.

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды