Advanced Instruments 4250 Скачать руководство пользователя страница 115

Страница: 115 / 121

International concern about environmental pollution resulting from

improper disposal of products and materials at the end of their useful

life has resulted in an increase in legislation to control the methods and

procedures used to handle waste electrical and electronic equipment.

While the regulatory status in some regions of the world has progressed

to the point where formal legislation is already in effect, many other

regions are in the process of creating similar legislation or adopting that

already in existence in other areas. The result in the years ahead will be

more stringent control over disposal of products and recycling of their

components once they are withdrawn from use.

Since regulations governing the disposal of your instrument and acces-

sories may vary depending upon your geographic location, the following

guidelines are provided to assist you in identifying the options available

to you once the decision has been made to replace or dispose of this

product:

• Contact the supplier who sold you the product. Whether this was

Advanced Instruments itself, or one of its authorized dealers, this

supplier should be knowledgeable about the national and local

regulations governing disposal and recycling of products in your

area. In some cases, this supplier may be legally obligated to

accept the product from you and arrange for proper disposal or

recycling with no further involvement on your part. Alternately,

the supplier can provide you with specific instructions for actions

that you can take to dispose of the product properly.

Product Disposal and

Recycling

Appendix G

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды