Advanced Instruments 4250 Скачать руководство пользователя страница 66

Страница: 66 / 121

A foreign object has fallen into the product.

The product has been dropped or damaged by a falling object.

There are noticeable signs of overheating or a burning odor.

The product does not operate normally when you follow the oper-

ating procedures.

The main supply fuse(s) or any internal fuse(s) continually fail.

•

A discharge of static electricity from contact with the human body or

other conductor may damage system boards or static sensitive

devices. Never perform internal maintenance without following rec-

ommended static protection procedures.

•

The product is equipped with operator accessible fuses. If a fuse

blows, it may be due to a power surge or failure of a component.

Replace the fuse only once. If the fuse blows a second time, it is

probably caused by failure of a component part. If this occurs, refer

service to qualified service personnel. Always replace the fuse with

one of the same rating, voltage, and type. Never replace the fuse

with one of a higher current rating.

•

When servicing the product, use only factory-specified parts.

•

The product contains an integral lithium battery that is not user-

serviceable.

WARNING:

When returning this product for service, or shipping this

product to a second location, remove all heat transfer

fluid and hazardous specimens and decontaminate the

product before packaging for shipment. If the product

cannot be decontaminated, consult with your shipping

agent on appropriate packaging and marking.

Obtaining service

Before contacting Advanced Instruments for Hot-Line

Service, be sure

to read through this user's guide for instructions on routine adjustments,

Advanced

Cryoscope Model 4250 User’s Guide

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды