Advanced Instruments 4250 Скачать руководство пользователя страница 52

Страница: 52 / 121

8. Dis/Enable Xon/Xoff

This menu item enables or disables the Xon/Xoff

“

handshaking

”

proto-

col for RS-232 communication (CTRL-”S” = STOP/ CTRL-”G” = GO).

1. At

“

Dis/Enable Xon/Xoff

”

, press

START

to display

“

[on] <

Xon/Xof * [off]

”

. The current setting is indicated by the symbol,

“

2. At

“

[on] < Xon/Xof * [off]

”

, press

to enable or disable ser-

ial-port Xon/Xoff handshaking.

3. Press

ENTER

to store the new setting (or

STOP

to restore the

original setting).

9. Serial Number

“

Serial Number

”

, press

START

to display the instrument serial

number (

“

Serial #: 123

”

). Press

STOP

to return to the setup menu. This

number is set by the factory and cannot be changed by the operator.

10. Select Plateau Mode

This menu item enables changing the way the 4250 evaluates the

plateau. An idealized, dimensionless freezing point plateau is illustrated

and described in Figure 1.

1. At “

Select Plateau Mode

”, press

START

to display the current

mode.

2. Press

to toggle between plateau-seeking and timed-plateau

detection modes.

3. Press

ENTER

to store the new setting (or

STOP

to restore the

original setting).

11. Set % DFB

This menu item enables storing a

“

base

”

freezing point in the instrument

memory and displaying, with each sample test result, the percent differ-

ence between the test result and the stored base.

Advanced

Cryoscope Model 4250 User’s Guide

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды