Advanced Instruments 4250 Скачать руководство пользователя страница 91

Страница: 91 / 121

Troubleshooting Table

“Event Record Lost”

“Fan System Failure”

“FPE_INTOFLOW”

“FPE_INTDIV0”

“FPE_INVALID”

“FPE_ZERODIVIDE”

“FPE_OVERFLOW”

“FPE_UNDERFLOW”

“FPE_INEXACT”

“FPE_STACKFAULT”

“FPE_EXPLICITGEN”

“FPE_UNDEFINED”

“Head Not Down”

This message indicates that the event record

stored in memory has been corrupted. Try

restarting your instrument. If this does not

solve your problem, contact Advanced

Instruments for Hot-Line Service.

Check to make sure that the fan is plugged

in, and that the fan isn’t blocked. Check the

fan driver LED on the application board. Try

restarting your instrument. If this does not

solve your problem, contact Advanced

Instruments for Hot-Line Service.

Turn unit off and on. If the error message

does not persist and no other error message is

displayed, ignore this message. If the error

persists, contact Advanced Instruments for

Hot-Line Service.

This error indicates that the sensor at the

head down position was not tripped. Clear

any blockage and try restarting your instru-

ment. If this does not solve your problem,

contact Advanced Instruments for Hot-Line

Service.

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды