Advanced Instruments 4250 Скачать руководство пользователя страница 90

Страница: 90 / 121

Advanced

Cryoscope Model 4250 User’s Guide

“Calibration out of

Range; Repeat”

“Cooling System

Error”

“Count Error:

Parameter RAM”

EPROM Failure

“Error Reading

Barcode”

“ESC TRAP”

If you see this message, verify that your

operator technique is correct. Then, recali-

brate. If the problem persists, contact

Advanced Instruments for Hot-Line Service.

If you receive this message, check to make

sure that the thermoelectric is plugged in,

check the thermoelectric LED on the appli-

cation PCB, then try restarting your instru-

ment. Second, check that your instrument’s

cooling chamber contains enough heat trans-

fer fluid. If the problem persists, contact

Advanced Instruments for Hot-Line Service.

Turn unit off and on. Custom settings and

probe bin numbers may need to be reset. If

the error persists, contact Advanced

Instruments for Hot-Line Service.

This message indicates a memory error with

your FLASH memory. Try restarting your

instrument, and ignore if it does not reoccur.

Check to see if barcode scanner is damaged.

Make sure that the barcode is no longer than

13 characters. Cancel barcode and repeat

reading.

Turn unit off and on. If the error message

does not persist and no other error message

is displayed, ignore this message. If the

error persists, contact Advanced Instruments

for Hot-Line Service.

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды