Advanced Instruments 4250 Скачать руководство пользователя страница 53

Страница: 53 / 121

1. At

“

Set % DFB

”

, press

START

to display

“

Base Reading = xxx

”

The freezing point units will be the same as the units selected for

the regular freezing point test displays.

2. Press

CLEAR

to set the base to 0. Then use the numeric keypad

to enter the base value required.

3. When the base is set as required, press

ENTER

to save the setting

and return to the display to

“

Set % DFB

”

4. At

“

Set % DFB

”

, press

STOP

to return to the display

“

Cryoscope

Ready

”

12. Select Display mH/mC

This menu item enables changing the readout temperature units (see

Foreword for a discussion of the units of measurement used for milk

cryoscopy).

CAUTION

Changing this setting requires changing the % DFB set-

ting (if not set at zero), as well. (See

Set % DFB

, above.)

Changing this setting will erase all data stored in Recall and

Statistics memory.

1. At “

Select Display mH/mC

”, press

START

to display “

[mH] <

Display * [mC]

”.

2. At “

[mH] < Display * [mC

]”, the current setting is indicated by

the symbol “*”. Press < or > to toggle the display readout

between mH and mC.

3. Press

ENTER

to store the new setting (or

STOP

to restore the

original setting).

13. Select Language

This menu item enables selecting one of the alternate language display-

panel messages.

Instrument Operation

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды