Advanced Instruments 4250 Скачать руководство пользователя страница 93

Страница: 93 / 121

Troubleshooting Table

Your instrument was unable to detect a freez-

ing plateau, and was therefore unable to give

a result. Check your technique and try again.

If the message persists, obtain Hot-Line

Service.
Try restarting your instrument. If this does not

solve your problem, Contact Advanced

Instruments for Hot-Line Service.
This informative message tells you that a new

software version has been installed since you

last powered the instrument.
This informative message tells you that the

information stored in parameter RAM has

been corrupted. The instrument will reload

factory defaults.
Make sure there is paper in the printer. If

there is not, install paper per the instructions

in Chapter 1, Installation and Setup. If there is

paper in the printer, make sure that the printer

cover is completely and securely closed.
Check to make sure the paper roll is properly

installed per the instructions in Chapter 1,

Installation and Setup. The paper must be

feeding from the bottom of the roll, as shown

in Figure 3.
This message indicates a memory error with

the system RAM. Try restarting your instru-

ment and ignore if it does not reoccur. Your

instrument may load factory defaults.

“No Plateau, Repeat

Test”

No response when the

START or TEST key is

pressed.
“New Software

Version”

“Parameter RAM

Failed”

Printer fails to print

Printer advances paper

and appears to be print-

ing, but the paper is

blank.

“RAM Failure”

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды