Advanced Instruments 4250 Скачать руководство пользователя страница 70

Страница: 70 / 121

Stir/Freeze Wire Alignment section for proper alignment of the sample

probe and the stir wire. Refer to the Stir/Freeze Amplitude Adjustment

section to properly adjust the stir and freeze amplitudes.

Check error messages.

The software of your instrument is designed in

such a way that any incomplete task will be associated with an error

message, many self-explanatory, that will help you discover the source

of your problem. You can find all error messages and descriptions of

what they mean in Appendix A.

Internal diagnostic tests

The diagnostic menu allows any of a series of tests to be run to check

one functional subsystem of the instrument, or to perform some neces-

sary adjustment or setup.
An item on the

TEST

menu may be selected in either of the following

two ways:
• At

“

Select Test Item

”

, repeatedly press the

key to step the display

forward or

to step the display backward through the list. The list is

cyclic; pressing

at the last item cycles the display to item 0.

Continue pressing

until the desired test is displayed. While

the desired test is displayed, press the

START

key.

• Or, at

“

Select Test Item

”

, press the

START

key. The display will

change to

“

Test Menu #: 0

”

. Type the number of the desired test on

the numeric keypad. The

“

”

on the display will change to the num-

ber typed, if valid. Then press

ENTER

. The display will show the

selected test. Next, press the

START

key.

At “

Select Test Item

”, the following tests are available:

1. Statistics

The statistics option allows you to recall the stored results from a select-

ed last number of tests and calculate their average, standard deviation

and coefficient of variance. To use this option, use the following proce-

dure.

Advanced

Cryoscope Model 4250 User’s Guide

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды