Advanced Instruments 4250 Скачать руководство пользователя страница 55

Страница: 55 / 121

2. Each press of the START keypad will produce an additional one-

second freeze pulse.

3. Pressing the “>” key will increase the setting up to a maximum of

255. Pressing the “<” key will decrease the setting to a minimum

of 150.

4. Press

ENTER

to store the new setting (or

STOP

to restore the

original setting).

Using the Model 4250’s RS-232 port (Figure 7)

The RS-232 port allows you to output to an external device, such as a

computer. Almost every item of information displayed by your instru-

ment is also transmitted over the RS-232 port, including test results, all

error messages, and most display data from the diagnostic menu.
The default serial data rate for communications is 9600 bps (bits per

second), though you may alternatively select 1200, 2400, 4800, and

19200 bps.
The DB-9 RS-232 port on your instrument conforms to the DTE

EIA-232C standard and can reliably communicate over shielded cable

up to 10 meters in length, depending on the baud rate you use.

NOTE

• Your instrument is only designed to support unidirectional

communication with an external device. At this time, there

is no protocol for bidirectional communication.

• For a sample RS-232 Port Setup, please see the RS-232

Supplemental Information, Appendix E at the end of this

user’s guide.

• This instrument requires the use of a null modem RS-232C

cable. There are several variations on null modem cables.

Advanced Instruments. recommends that you purchase a RS-

232C cable direct from our factory.

Instrument Operation

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды