Advanced Instruments 4250 Скачать руководство пользователя страница 9

Страница: 9 / 121

Safe Use

• Route power cords so that they will not be walked on, tripped on, or

pinched by items placed upon or against them. Pay particular atten-

tion to the plug, electrical outlet, and the point where the cord exits

the product.

• Do not pull on cords and cables. When unplugging cords or cables,

grasp the corresponding connector.

• Do not install or use this product in any area subject to extreme

short-term temperature variations, or locations that exceed the speci-

fied operating environment temperatures.

• Never use this product in a wet area.
• To avoid injury or fire hazard, do not operate this product in an

explosive atmosphere.

• Do not install or use the product on an unstable, non-level work sur-

face.

• Do not operate this product with the covers removed or unsecured.

FCC Requirements

•

WARNING

: Changes or modifications to this unit not expressly

approved by Advanced Instruments could void the user’s authority

to operate the equipment.

• This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды