Advanced Instruments 4250 Скачать руководство пользователя страница 41

Страница: 41 / 121

Instrument Operation

Before testing samples

Like most measuring instruments, cryoscopes need calibration against

standards. Your 4250 was calibrated at -408 m°C and -600 m°C at the

factory. The probe and calibration parameters are stored in parameter

RAM which is powered by an internal battery when the instrument

power is off or disconnected. Thus, when

“

Cryoscope Ready

”

is dis-

played, your 4250 cryoscope is calibrated and ready to run. However,

the calibration should always be verified during operation to be sure

that none of the parameters affecting calibration have changed (if recali-

bration is required, see Chapter 4).
Instrument operation in the following manner is recommended:
1. Remove the sample tube from the freezing chamber (see Figure 5,

Item 8).

2. Gently wipe the probe, stir/freeze wire, mandrel and the top of the

freezing chamber (in that order) with a soft, lint-free, non-ionic

paper tissue dampened with distilled water to remove anything that

might contaminate the sample to be tested. Be careful not to bend

the probe or stir/freeze wire.

3. Select a reference solution or NaCl standard with a freezing point

close to that expected for your unknown (Advanced Lactrol

530 is

recommended for milk). Swirl and carefully open an ampule of the

reference solution (or NaCl standard) selected.

4. Select a clean sample tube (see page 20, Repeatability Tips).
5. Pipette or measure a sample of the selected reference solution or

NaCl standard into the clean sample tube and place the tube in the

freezing chamber.

6. Press the

START

key.

“

I.D. #

”

has been enabled via the setup menu (see page 27), the

instrument operator will be prompted for a sample or user identifi-

cation number of up to 13 digits at this time from either the keypad

or optional barcode scanner.

Содержание 4250


























































































































Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды

Advanced Instruments 4250, Руководство пользователя

Результаты поиска

Содержание 4250

Отзывы:

Бренды по названию

Популярные бренды