ADEMCO VistaKey-SK Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 108

background image

Section 3 – Quick Installation

3–3

Initial System Test

ACS access grants and egress grants are alarm type events in the alarm panel log. If you have
changed the default values for “Event Log Types” (alarm panel field 1*70) so that alarm type
events are not logged, the following procedure can not be used. To use this procedure, refer to
the

“Data Field Program Mode”

descriptions in your alarm panel installation and setup guide and

temporarily enable alarm type events in field 1*70 to perform this test.

Check the operation of the VistaKey to verify that the installed hardware is functional by
performing the following procedure.

1. Using any of the alarm control panel keypads, enter Installer

Code + # + 78. The keypad displays:

ACS TEST MODE
0 = quit

0

2. Press 2 on the keypad. The keypad displays:

ACS TEST MODE
GRANT ALL CARDS

2

3. Press [

✲

] on the keypad. The keypad starts beeping at a periodic

rated indicating the system is in the test mode and the keypad
displays:

GRANT ALL CARDS
ACS TEST MODE

4. Swipe any ADEMCO proximity card past the card reader. If the unit is properly installed,

the mag lock or door strike activates, and the green LED temporarily illuminates on the
card reader. If the test is successful, advance to step 5. If the mag lock or door strike does
not activate, and the green LED does not illuminate, do the following:

a. Exit the ACS TEST MODE by entering Installer Code + # +

78 + 0 + *. The keypad stops beeping and displays

:

****DISARMED****

READY TO ARM

b. Check all wiring to the units and that external power is applied.

c. Return to Step 1 and repeat the test.

5. If additional VistaKeys have been installed for additional access points, repeat step 4 at

the card reader for each of the additional access points.

6. Exit the ACS Test Mode by entering Installer Code + # + 78 +

0 + * at the keypad. The keypad stops beeping and displays:

****DISARMED****

READY TO ARM

7. Verify that all access points tested are logged in the alarm panel’s event log by using the

following procedure.

a. Using any of the alarm panel keypads, enter Installer Code

+ # + 60 to view the alarm panel control log. The keypad
displays:

ENTER 0= RECENT
1=COMPLETE DUMP

b. Press 1 on the keypad. The keypad displays:

SCAN LOG BY PART
0=NO 1-8=PART #

c. Press 0 on the keypad. The keypad displays:

ALARM EVENT LOG
TYPE CCC UUU

d. Press 3 on the keypad repeatedly until the keypad displays:

ALL EVENT LOG
TYPE CCC UUU

e. Press 8 on the keypad. The keypad display shows the most recent event in the log.

f. Press 1 on the keypad to step back through the event log to verify that all access points

tested are in the log. The first line of the log provides a partition number, date, and
time. The second line of the display for the access point test shows “ACS GRT” or “EGR
GRT” followed by a 3-digit zone number and user number of U999. Note that U999

«
...
27
28
29
30
31
...
»

Содержание VistaKey-SK













































































































Отзывы:

Нет отзывов

Похожие инструкции для VistaKey-SK

Max Charge MC-624

Бренд: Balmar Страницы: 8

MAX CHARGE MC-614

Бренд: Balmar Страницы: 20

Бренд: CORNING Страницы: 142

Бренд: Case IH Страницы: 81

VARIOMATIC SARV 07.1

Бренд: AUMA Страницы: 32

Бренд: YASKAWA Страницы: 12

ESP32-C3 Series

Бренд: Espressif Systems Страницы: 30

Series RHCN-7000

Бренд: Omega Engineering Страницы: 2

Бренд: WAM Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Ultraflex Страницы: 48

Бренд: Ulvac Страницы: 48

Бренд: Oilon Страницы: 74

CapSense Plus CY3280-CPM1

Бренд: Cypress Страницы: 4

Бренд: Thundercomm Страницы: 8

Бренд: Altronix Страницы: 20

DS-K1F600U-D6E Series

Бренд: HIKVISION Страницы: 49

Бренд: DEVI Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды