ADEMCO VistaKey-SK Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 108

background image

Section 5 - Programming

5–29

•

ACS Trace (To obtain a report for Trace, the ACS Group Trace or Cardholder Trace must
also be turned on.)

NOTE: See Section 8: Event Log for a listing of the events and report codes that make up
each of these categories.

The system contains provisions that allow you to change the program defaults so that reports
are sent for any or all of these event categories. To change the defaults in the program, enter
the Data Field Program Mode using the procedures in your alarm system manuals. The
keypad displays:

Program Mode
* Fill # View

–00

Press

✲

94. The following screen appears.

Program Mode
* Fill # View

100

Press

✲

35. The following screen appears.

ACS Dlr Enables

135

This field requires the entry of 6 digits. The entries for this field are
as follows:

ENTRY
ORDER

EVENT

ENTRY

1

ACS Trace

Always press 1 if reports are to be sent
for Trace. Press 0 only if no reports are
to be sent.

2

ACS TROUBLES

Press 1 to enable or 0 to disable ACS
trouble reporting.

3

ACS BYPASSES

Press 1 to enable or 0 to disable ACS
bypass reporting.

4

Reserved

Press 1 or 0. This entry is required as a
placeholder in the six-digit string.

5

ACS SYSTEM

Press 1 to enable or 0 to disable ACS
system reporting.

6

ACS ALARMS

Press 1 to enable or 0 to disable ACS
alarm reporting.

The keypad beeps three times after you enter the sixth digit.

Press [

✲

]. The following screen appears.

Enter Fill Field

1

Press #99. The following screen appears.

Program Mode
* Fill # View

–00

Press #99 again. The Data Field Programming Mode ends.

#73 Keypad Entry Enable

The #73 command may be used (if enabled) to grant entry or exit through an access point in
the partition that the keypad is connected to. The access point automatically relatches after
the time interval set by the previously defined door open time. For the #73 command to be
accepted, the following conditions must exist.

•

The keypad must be attached to the partition where the access point is located.

•

If the partition is armed and Armed Restriction is in effect, the user must be authorized to
disarm the partition.

«
...
67
68
69
70
71
...
»

Содержание VistaKey-SK













































































































Отзывы:

Нет отзывов

Похожие инструкции для VistaKey-SK

Бренд: Talgil Страницы: 14

M-DUINO PLUS series

Бренд: Industrial Shields Страницы: 46

Бренд: Anritsu Страницы: 74

Бренд: Adaptec Страницы: 4

Бренд: zeeltronic Страницы: 13

Бренд: QD Dynamics Страницы: 64

Бренд: OCL Страницы: 2

Бренд: OBO Bettermann Страницы: 6

Бренд: Furious FPV Страницы: 15

Бренд: GS Страницы: 236

YukonDrive-1021

Бренд: Harmonic Drive Страницы: 53

Бренд: Wahlberg Страницы: 40

Бренд: MRC Страницы: 2

Goldstart MPC2000

Бренд: P&B Страницы: 41

Бренд: Lennox Страницы: 12

Бренд: MAC3 Страницы: 20

Бренд: Martin Audio Страницы: 1

Бренд: Hyster Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды