ABB i-bus KNX Yucus YUB/U1.0.1 Series Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

84

receive on the 1-bit communication object "Enable". The function is block if an OFF
telegram is receive on the 1-bit communication object "Enable". This means that no
telegram is sent out on the "Output" communication object.

12.27.4

Extended parameter – Group object value

Options

Normal
Inverse

Note: This object is only adjustable if the "Enable object" parameter is set to

"activated".

The enable function normally functions as follows:
The function is active if an ON telegram is receive on the 1-bit communication object
"Enable". The function is block if an OFF telegram is received on the 1-bit communication
object "Enable".

Via the parameter "Logic of the enable function", the above-described behavior can be
reversed, i.e. if an ON telegram is received on the 1-bit communication object "Enable",
the function is blocked. The function is active if an OFF telegram is received on the 1-bit
communication object "Enable".

12.27.5

Extended parameter – Enable group object after return of voltage

Options

No
Yes

Note: This object is only adjustable if the "Enable object" parameter is set to

"activated".

The parameter "Enable after return of voltage" exists to permit a defined behavior at the
"Enable" communication object after a return of bus voltage. A determination is made
here about whether a "1" ("enable") or a "0" ("blocked") is present on the enable object
after the return of bus voltage.

Note: If the logic of the enable function is set to "inverse", the behavior is also inverted
after the return of bus voltage, i.e. if the parameter "enable after return of bus voltage" is
set to "enable", and at the same time the "logic of the enable function" is parameterized
to "inverse", then the function will initially not be active after return of bus voltage. This
must first be activated via the receipt of an OFF telegram on the enable object.

«
...
83
84
85
86
87
...
»

Содержание i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i-bus KNX Yucus YUB/U1.0.1 Series

Бренд: Panasonic Страницы: 68

Бренд: Panasonic Страницы: 20

Бренд: Hach Страницы: 2

Бренд: Hach Страницы: 12

Бренд: Hach Страницы: 472

Бренд: Hach Страницы: 64

Бренд: Hach Страницы: 210

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 157

Бренд: Lawler Страницы: 4

Бренд: QTP Страницы: 2

Бренд: National Instruments Страницы: 6

Бренд: Centurion Страницы: 16

Бренд: Guangdong Schen Investment Страницы: 15

Бренд: OCTANORM Страницы: 6

Бренд: Tekmar Страницы: 2

SmartLoop KTSL-FC1-UV-KO

Бренд: Keystone Страницы: 2

TROVIS 6495 Series

Бренд: Samson Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды