ABB i-bus KNX Yucus YUB/U1.0.1 Series Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

113

"Heating with additional stage" or "Heating and cooling with additional stages", only
available when the "Extended settings" parameter under "Control of heating additional
stage" is set on "Yes".

The mode of the control value can be used to adapt the control value to de-energized
opened (normal) or de-energized closed (inverse) valves.

– N

ormal

: Value 0 means "Valve closed".

–

Inverse

: Value 0 means "Valve open".

12.34.35

Additional heating stage– Hysteresis (x 0.1 °C)

Options

Input from 3 to 255

Note:

Only available when the "Device function" parameter is set on either

"Single device" or "Master device" and the control function parameter is set on either
"Heating with additional stage" or "Heating and cooling with additional stages", only
available when the "Control value type" parameter is set either on "2-point 1 Bit, Off/On"
or "2-point 1 Byte, 0/100%".

The hysteresis of the two-point controller specifies the fluctuation range of the controller
around the setpoint value. The lower switching point is located at "Setpoint value minus
hysteresis" and the upper point is at "Setpoint value plus hysteresis".

12.34.36

Additional heating stage – Control value difference for sending of heating

control value

Options

2 %
5 %
10 %
Send cyclic only

Note:

Only available when the "Device function" parameter is set on either

"Single device" or "Master device" and the control function parameter is set on either
"Heating with additional stage" or "Heating and cooling with additional stages", only
available when "Control value type" parameter is set either on "PI continuous, 0 – 100%"
or "Fan coil".

The control values of the 0 - 100% PI continuous controller are not transmitted after every
calculation. Instead, they are transmitting when the calculation results in a value that is
different enough to the previous sent value to make a transmission meaningful. This value
difference can be entered here.

«
...
112
113
114
115
116
...
»

Содержание i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i-bus KNX Yucus YUB/U1.0.1 Series

Бренд: Galcon Страницы: 35

Бренд: U.S. Divers Страницы: 22

Бренд: Pangolin Страницы: 35

Бренд: NDS Страницы: 20

Бренд: FASTRON. Страницы: 37

Бренд: Festo Страницы: 2

Бренд: Belimo Страницы: 2

Бренд: Duke Страницы: 4

Бренд: Delta Страницы: 9

Бренд: RollSeal Страницы: 58

SNAP PAC S Series

Бренд: OPTO 22 Страницы: 70

KNX SA 16M230 SMI REG

Бренд: WAREMA Страницы: 6

Бренд: Banner Страницы: 16

EL-FLOW Prestige series

Бренд: BRONKHORST Страницы: 57

Xtracontrol DC2

Бренд: Infranor Страницы: 87

Бренд: CD Automation Страницы: 62

Бренд: Magnetek Страницы: 9

Бренд: FRC Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды