ABB i-bus KNX Yucus YUB/U1.0.1 Series Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

149

"Window contact", "Control On/Off", "Presence detector" and "Operating mode (listed in
decreasing order of priority).

12.35.2

General – Superimposed operating mode - Object no

Object name

Data type

Flags

Superimposed

operating

mode

1 byte DPT 20.102

C, W, T, U

Superimposed

operating

mode – (master / slave)

1 byte DPT 20.102

C, W, T, U

Item 2: If the master/slave mode is active, the "Superimposed operating mode" object of
the master and the slave must be connected to the group address of the transmitter.

The "Superimposed operating mode" object receives the operating mode that is to be set
as 1- byte value. Here value 0 means "Superimposition inactive", value 1 "Comfort", value
2 "Standby", value 3 "Economy" and value 4 "Frost/heat protection". In addition to manual
setpoint adjustment and the adjustment of the basic setpoint value, the setpoint
temperature of the controller can also be defined by objects "Superimposed operating
mode", "Condensate ware alarm", "Dew alarm", "Window contact", "Control On/Off",
"Presence detector" and "Operating mode (listed in decreasing order of priority).

12.35.3

General – In operation - Object no

Object name

Data type

Flags

Send in operation

1 bit DPT 1.001

C, T

The controller uses this 1-bit communication object to send a cyclical "sign of life". This
signal can be used to monitor the device, e.g. by means of a visualization.

12.35.4

General – Additional functions/objects – Control on/off - Object no

Object name

Data type

Flags

1. Control on/off

1 bit DPT 1.001

C, W, T, U

2. Control on/off – (master)

1 bit DPT 1.001

C, R, W, T, U

3. Control on/off – (slave)

1 bit DPT 1.001

C, W, T, U

Item 2: During active ON/OFF controller function in master/slave mode the ON/OFF
(master) control object is to be link with this object.
Item 3: During active ON/OFF controller function in master/slave mode the ON/OFF
(slave) control object is to be link with this object.

«
...
148
149
150
151
152
...
»

Содержание i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i-bus KNX Yucus YUB/U1.0.1 Series

Бренд: National Instruments Страницы: 7

Бренд: National Instruments Страницы: 16

Бренд: ABB Страницы: 17

Бренд: SOMFY Страницы: 56

RSF B mini Series

Бренд: Harmonic Drive Страницы: 33

Бренд: Swegon Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: LOVATO ELECTRIC Страницы: 18

Бренд: adept technology Страницы: 96

Бренд: InnoMedia Страницы: 10

Бренд: JR Страницы: 88

Бренд: Danfoss Страницы: 18

Бренд: Zapi Страницы: 39

Бренд: SOMFY Страницы: 20

Бренд: MRC Страницы: 2

Princeton Applied Research PARSTAT 2273

Бренд: Ametek Страницы: 26

Бренд: CSZ Страницы: 69

Бренд: Vega Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды