ABB i-bus KNX Yucus YUB/U1.0.1 Series Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

132

Note: Only available when the "Device function" parameter is set on either

"Single device" or "Master device".

The current setpoint value can be sent to the bus either cyclically and after a change, or
only after a change.

12.34.86

Setpoint setting – Cyclic sending of the current setpoint temperature (min)

Options

Time input from 5 to 240

Note: Only available when the "Device function" parameter is set on either

"Single device" or "Master device" and only available when the "Send current setpoint" is
set on "Cyclic and during change".

This parameter is use to specified the amount of time that will elapse before the current
setpoint value is automatically transmitted onto the bus line.

12.34.87

Setpoint setting – Basic setpoint is

Options

Setpoint for cooling comfort
Setpoint for heating comfort
Mean value between heating comfort and cooling
comfort

Note: Only available when the "Device function" parameter is set on either

"Single device" or "Master device"

This parameter is used to specified the reference for basic setpoint.

12.34.88

Changing set value – Maximum manual increase during heating mode (°C)

Options

Input from 0 to 9

Note: Only available when the "Device function" parameter is set on either

"Single device" or "Master device", and the Control function parameter is set on “Heating”,
“Heating with additional stage”, "Heating and cooling" or "Heating and cooling with
additional stages".

«
...
131
132
133
134
135
...
»

Содержание i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i-bus KNX Yucus YUB/U1.0.1 Series

Бренд: C-TEC Страницы: 2

Бренд: NAVITAS Страницы: 7

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренд: Walchem Страницы: 126

Бренд: Elby Designs Страницы: 4

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Quickie Страницы: 64

by-me Eikon 20526

Бренд: Vimar Страницы: 6

Бренд: AirCycler Страницы: 2

Torque Converter Lock-Up

Бренд: TS Performance Страницы: 4

Бренд: Wavelength Electronics Страницы: 17

Бренд: turck Страницы: 45

Бренд: ADLINK Technology Страницы: 37

Бренд: Samwon Tech Страницы: 104

Бренд: Jordan Valve Страницы: 5

Бренд: Quicksmart Страницы: 10

Бренд: Aerotech Страницы: 112

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды