ABB i-bus KNX Yucus YUB/U1.0.1 Series Скачать руководство пользователя страница 119 | Manualshive

Страница: 119 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

118

– N

ormal

: Value 0 means "Valve closed".

–

Inverse

: Value 0 means "Valve open".

12.34.48

Basic stage cooling – Hysteresis (x 0.1 °C)

Options

Input from 3 to 255

Note:

This parameter is only available when the "Control value type" parameter

is set either on "2-point 1 Bit, Off/On" or "2-point 1 Byte, 0/100%".

The hysteresis of the two-point controller specifies the fluctuation range of the controller
around the setpoint value. The lower switching point is located at "Setpoint value minus
hysteresis" and the upper point is at "Setpoint value plus hysteresis".

12.34.49

Basic stage cooling – Control value difference for sending of cooling control

value

Options

2 %
5 %
10 %
Send cyclic only

Note:

This parameter is only available when "Control value type" parameter is

set either on "PI continuous, 0 – 100%" or "Fan coil".

The control values of the 0 - 100% PI continuous controller are not transmitted after every
calculation. Instead, they are transmitting when the calculation results in a value that is
different enough to the previous sent value to make a transmission meaningful. This value
difference can be entered here.

12.34.50

Basic stage cooling – Cyclic sending of the control value (min)

Options

Input from 1 to 60

Note

: This parameter is only available when "Control value type" parameter is

set either on "PI continuous, 0 – 100%", "PI PWM, On/Off“ or "Fan coil".

The current control value used by the device can be cyclically transmit to the bus.

«
...
117
118
119
120
121
...
»

Содержание i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i-bus KNX Yucus YUB/U1.0.1 Series

Micro850 series

Бренд: Allen-Bradley Страницы: 24

Бренд: Olsen Страницы: 4

Бренд: Linear Technology Страницы: 32

Бренд: OBO Bettermann Страницы: 6

Бренд: JR Страницы: 88

Бренд: Kapego LED Страницы: 12

Бренд: Xinje Страницы: 41

Бренд: roco Страницы: 128

Бренд: Vestax Страницы: 4

Бренд: KRAL Страницы: 16

Бренд: Omega Страницы: 73

M-TYPE PREMIUM COMMANDER

Бренд: DURKOPP ADLER Страницы: 74

Бренд: Omega Engineering Страницы: 2

AquaController Apex

Бренд: Neptune Systems Страницы: 5

Бренд: D+H Страницы: 2

DRR245-21-ABC-T

Бренд: Pixsys Страницы: 109

Бренд: Belden Страницы: 4

Emotron VS10 Series

Бренд: CG Products Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды