ABB i-bus KNX Yucus YUB/U1.0.1 Series Скачать руководство пользователя страница 165 | Manualshive

Страница: 165 / 173

background image

KNX Technical Reference Manual
ABB i-Bus

®

KNX Yucus

164

12.36.14

Fan – The code number of the Fan Speed 5

Options

Input from 0-255

This parameter is used to specify the 1Byte value corresponding to the fifth level fan
speeds. As there are many different types and brands of VRV air conditioner system KNX
protocol interface gateway in the market, the 1Byte value corresponding to the fifth level
of fan speeds could also be different. Therefore, please refer to the VRV air conditioning
system KNX protocol interface gateway manual to obtain the correct corresponding 1Byte
value of the fifth level fan speed. If the 1Byte value of the fifth level fan speed define by
this parameter does not match the value of the VRV air conditioning system KNX protocol
interface gateway, device would not be able to control the fifth level fan speed.

12.36.15

Fan – Activate Auto Fan Speed

Options

Activate
Deactivate

This parameter is used to define whether the automatic fan speed of the VRV air
conditioner would be active or not active. Please refer to the VRV air conditioning system
manual to check whether does the VRV air conditioner system allow the control of
automatic fan speed. If this parameter is activated and VRV air conditioner system itself
does not allow the control of automatic fan speed, device would not be able to control the
automatic fan speed of the VRV air conditioner system

12.36.16

Fan – The code number of Auto Fan Speed

Options

Input from 0-255

This parameter is used to specify the 1Byte value corresponding to the automatic level
fan speeds. As there are many different types and brands of VRV air conditioner system
KNX  protocol  interface  gateway  in  the  market,  the  1Byte  value  corresponding  to  the
automatic level of fan speeds could also be different. Therefore, please refer to the VRV
air  conditioning  system  KNX  protocol  interface  gateway  manual  to  obtain  the  correct
corresponding  1Byte  value  of  the  automatic  level  fan  speed.  If  the  1Byte  value  of  the
automatic level fan speed define by this parameter does not match the value of the VRV
air  conditioning  system  KNX  protocol  interface  gateway,  device  would  not  be  able  to
control the automatic level fan speed.

Note: The values corresponding to various wind speeds cannot be the same

12.36.17

Changing set values – Max. setpoint (

°C)

Options

Input from 0-40

This parameter is used to define the maximum temperature adjustment of the VRV mode.
Please refer to the VRV air conditioning system manual to obtain the highest temperature
that can be set by the VRV air conditioner system. If the maximum temperature define by
this parameter does not match the maximum temperature that can be set by the VRV air

«
...
163
164
165
166
167
...
»

Содержание i-bus KNX Yucus YUB/U1.0.1 Series














































































































































































Отзывы:

Нет отзывов

Похожие инструкции для i-bus KNX Yucus YUB/U1.0.1 Series

Бренд: Oceanic Страницы: 11

Бренд: T&D Страницы: 2

Бренд: Procom Страницы: 10

Бренд: Objective Imaging Страницы: 11

Бренд: MacroAir Technologies Страницы: 32

Бренд: McIntosh Страницы: 60

Бренд: Ruida Technology Страницы: 45

Бренд: Samcen Страницы: 65

Бренд: Brooks Страницы: 66

Бренд: LevelOne Страницы: 314

Бренд: ULTRAFRYER Страницы: 1

Бренд: dixell Страницы: 4

Бренд: Broan Страницы: 2

Бренд: Instrutech Страницы: 34

Бренд: Napoleon Страницы: 8

NEO Agility 48 10GbE Card

Бренд: Overland Storage Страницы: 4

Бренд: SSK Страницы: 8

Бренд: dunkermotoren Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды