manualshive.com logo in svg

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 96 / 110

Поделиться
Скачать
3D Systems CubePro 3D Printer Скачать руководство пользователя страница 96

TESTING THE PRINT JETS AND EXTRUDERS

When material fails to come out of the print jets during a print, you may receive a warning message on the
display. The CONTROL JETS function from the Print Jet Calibration menu is a utility that enables you to test
the print jet heating elements and the extruder operation.

Navigate to the Print Jet Calibration screen and select 

CONTROL JETS

.

1.

Select the print jet you wish to test.

2.

Select the target temperature value twice to read 260°C.

3.

NOTE: To increase or decrease the temperature value, press the up or down arrow.

NOTE: The typical printing temperature for ABS print material is 260°C. The typical

printing temperature for PLA material is 220°C. For best results, leave the default

target temperature at 260°C while extruding print material from the Control Jets test

utility.
NOTE: The current temperature reading will appear above the target temperature

value.

Once the temperature has reached 260°C, select the speed value.

4.

NOTE: Pressing the speed value twice will place the value at 4.0 RPM. Press the up or

down arrows to increase or decrease the extrusion speed.

Содержание CubePro 3D Printer















































































































Отзывы:

Нет отзывов