3D Systems CubePro 3D Printer Скачать руководство пользователя страница 17

Страница: 17 / 110

SETUP AND ACTIVATION

Select your language. Press the checkmark to conﬁrm your selection.

Enter a name for your printer. Scroll to the letters you wish to select by pressing the arrow symbols on each side of the screen. Press the letters to select

them. Select the

checkmark

to continue. If you do not wish to name your CubePro, press

SKIP

to move to the next screen and continue with step 4.

NOTE: The printer will search for area wireless networks.

Connect your printer to your wireless network. Use the up or down arrow to scroll to your network choice. Select your network.

NOTE: If your network is password protected, the printer will ﬁrst prompt you to enter

the password.
NOTE: The printer can also connect to an ad hoc network, a decentralized network

that wirelessly connects a local computer to the printer directly. The computer must

have a wireless adapter conﬁgured for ad-hoc mode. The adapter must use the same

SSID as is found in the printer. Connecting to an ad hoc network is discussed further

in the section titled

Setting Up an Ad Hoc Network

NOTE: Connection to a network is conﬁrmed when a checkmark appears to the left of

the network name. If the network is secured, a lock icon will appear to the right of the

network name.

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 17 / 110

Результаты поиска

Содержание CubePro 3D Printer

Отзывы: