manualshive.com logo in svg

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 3 / 110

Поделиться
Скачать
3D Systems CubePro 3D Printer Скачать руководство пользователя страница 3

INTRODUCTION

Thank you for purchasing the CubePro™ 3D engineering and prosumer printer. This printer allows you to
express your creativity like never before. With many different material colors to choose from, enjoy the
freedom to print in color or mix it up.

With its ready-to-print technology, the CubePro provides a new dimension to your imagination.

Copyright

©2016 by 3D Systems, Inc. All rights reserved. This document is subject to change without notice. This
document is copyrighted and contains proprietary information that is the property of 3D Systems, Inc. The
3D Systems logo is a registered trademark of 3D Systems, Inc. CubePro is a trademark of 3D Systems, Inc.
Use of the 

3DSystems.com

 website constitutes acceptance of its Terms of Service and Privacy Policy.

Compliance

FCC Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

NOTE: Changes or modifications to this equipment not specifically approved by 3D

Systems may void the user’s authority to operate this equipment.

KCC

이 기기는 가정용(B급) 전자파적합기기로서 주 로 가정에서 사용하는 것을 목적으로 하며, 모 든 지역에서 사용할 수 있습니다.

This equipment is home use (Class B) electromagnetic wave suitability equipment and to be used mainly
at home and it can be used in all areas.

This equipment conforms with International Electric Committee (IEC) 60950-1 and meets the requirements
of the applicable EC directives.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

Содержание CubePro 3D Printer















































































































Отзывы:

Нет отзывов