3D Systems CubePro 3D Printer Скачать руководство пользователя страница 25

Страница: 25 / 110

Print Plate Calibration

MOVE JETS

allows the user to manually move the print jets in the X and Y directions.

LEVEL PLATE

is a utility that assists in leveling the print pad to the print jets.

Print Jet Calibration

CONTROL JETS

allows the user to test the operation of the extruders and print jets.

OFFSET JETS

is a utility that deﬁnes the parameters of the space between the print jets.

CAUTION: Do not change any of the values in the OFFSET JETS utility unless advised to

do so by Cubify Support. Any changes will alter the print quality of your creations.

Network

The

Network

menu allows the user to connect to a wireless network or to an ad hoc device.

System

SELECT LANGUAGE

allows the user to localize the printer to their language.

LIGHT

allows the user to turn on or oﬀ the print jet LEDs. The other interior LEDs are managed by the

ﬁrmware when the CubePro is powered on.

Advanced

Selecting the

FIRMWARE

icon allows the user to update their ﬁrmware either with a ﬁle downloaded to a

USB mass storage device or by wireless connection.

By selecting

INFO

, the printer will display the printer status including the serial number, the print jet

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 25 / 110

Результаты поиска

Содержание CubePro 3D Printer

Отзывы: