3D Systems CubePro 3D Printer Скачать руководство пользователя страница 67

Страница: 67 / 110

NOTE: Ensure the material is not bent or creased. If the material is not straight, pull

out the damaged material from the cartridge. Cut oﬀ and dispose the portion that is

damaged.

Insert the material under the clamp roller and into the material tube. Select the

checkmark

to continue.

10.

Gently push the material into the print jet until molten plastic extrudes into the jet wiper. Select the

checkmark

to continue.

11.

NOTE: When the material reaches far enough into the print jet area, a feed motor will

assist with feeding the material into the print jet.

(1) Push the front of the cartridge into place and then (2) push the cartridge handle downward until the cartridge is fully seated in its mount. Select the

12.

checkmark

to continue.

NOTE: Ensure the front of the cartridge (A) where the material exits is seated under

the clamp roller and between the vertical alignment pins in the cartridge bay.

CAUTION: If replacing the third cartridge, be sure to rotate the second bay cartridge to

its vertical position before selecting the checkmark.

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 67 / 110

Результаты поиска

Содержание CubePro 3D Printer

Отзывы: