3D Systems CubePro 3D Printer Скачать руководство пользователя страница 51

Страница: 51 / 110

NYLON MANUAL SUPPORTS

Using Nylon Manual Supports

When printing with nylon, parts with large, ﬂat overhanging features may warp. CubePro software provides
readily-accessible nylon supports for your nylon-printed parts.

NOTE: The use of nylon manual supports requires INF support material to also be

installed in the printer and used as a support material type when setting the build

settings. INF support material is to be used in addition to the nylon supports you will

add to the part.

After loading your part to the print pad, select

Open Manual Support

Select the supports you will need by their height.

NOTE: The height is noted by the variables after the last X in the ﬁle name. You may

have to keep trying diﬀerent support sizes until you ﬁnd the one that contacts the

bottom surface of the part needing support.

NOTE: It is okay for the support to be taller than the bottom surface but the support

should not extrude above the part.

Add as many supports as you will need knowing that INF material will be printed around the supports providing additional stability.

NOTE: For best results, place supports under the corners of overhanging features.

NOTE: Once you move the supports into position, adding additional manual supports

will reset all of them and each one will have to be repositioned.

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 51 / 110

Результаты поиска

Содержание CubePro 3D Printer

Отзывы: