3D Systems CubePro 3D Printer Скачать руководство пользователя страница 10

Страница: 10 / 110

SPECIFICATIONS AND REQUIREMENTS

Dimensions And Weight

Dimensions

566.7 mm (w) x 581.0 mm (d) x 606.4 mm (h) (22 5/16” (w) x 22 7/8” (d) x 23 7/8” (h))

Weight Unboxed:

41 kg (90.7 lbs.)

43 kg (94.3 lbs.) Duo

44 kg (98 lbs.) Trio

Weight Boxed:

Maximum: 58.97 kg (130 lbs.)

Maximum: 59.87 kg (132 lbs.) Duo

Maximum: 60.78 kg (134 lbs.) Trio

PC Requirements

Windows 7, 8, 8.1 and 10

Multi-core processor - 2GHz or faster per core

System RAM - 2GB

Screen resolution - 1024 x 768 dpi

Software

CubePro Client Software - Available at

http://3dsystems.com/shop/cubepro/downloads

Electrical Requirements

100-240V AC 50-60 Hz auto switching, 6A

Material Storage

Although all polymers degrade with time, the following conditions help ensure the quality of the material:

Unpack the material only as needed

Store the material at 18-29°C (65-85°F)

Store the material enclosed in a dry environment (low humidity)

Use within 12 months of receipt

Содержание CubePro 3D Printer















































































































Результаты поиска

Содержание CubePro 3D Printer

Отзывы:

3D Systems CubePro 3D Printer, Руководство пользователя, Страница: 10 / 110

Результаты поиска

Содержание CubePro 3D Printer

Отзывы: